Abstract: This study addresses the use of a natural fiber (pig hair), a massive food-industry waste, as reinforcement in adobe mixes (a specific type of earthen material). The relevance of this work resides in the fact that earthen materials are still widely used worldwide because of their low cost, availability, and low environmental impact. Results show that adobe mixes' mechanical-damage behavior is sensitive to both (i) fiber dosage and (ii) fiber length. Impact strength and flexural toughness are increased, whereas shrinkage distributed crack width is reduced. Average values of compressive and flexural strengths are reduced as fiber dosage and length increase, as a result of porosity generated by fiber clustering. Based on the results of this work a dosage of 0.5% by weight of dry soil using 7 mm fibers is optimal to improve crack control, flexural toughness and impact strength without statistically affecting flexural and compressive strengths. (C) 2018 Elsevier Ltd. All rights reserved.

Abstract: Chile is facing important challenges to develop its energy sector. Estimations demonstrate that in its electricity consumption Chile will grow at an annual rate of 4.6% until 2030, despite ongoing efficiency improvements. To satisfy this demand in a sustainable way, the national energy policy promotes the integration of novel and clean power generation into the national power mix, with special emphasis on concentrated solar power (CSP). The present paper assesses the development of solar-based electricity generation in Chile by CSP, achieved by a Solar Power Tower plant (SPT) using molten salt as heat carrier and store. Such SPTs can be installed at different locations in Chile, and connected to the main national grid. Results show that each SPT plant can generate around 76 GWh(el) of net electricity, when considering solar irradiation as the sole energy source and at a 16% overall efficiency of the SPT process. For operation in a continuous mode, a hybrid configuration with integrated gas backup system increases the generating potential of each SPT to 135 GWh(el). A preliminary Levelized Energy Cost (LEC) calculation provides LEC values between 0.15 and 0.18 $/kWh, as function of the overall process efficiency and estimated investment cost. Chile's solar irradiation favors the implementation of SPT plants. (C) 2013 AIP Publishing LLC.

Abstract: Chile is expecting a 5.4% growth in energy consumption per year until 2030, requiring new and better solutions for the upward trend of its electricity demand. This state leads to select and study one of the potential alternatives for electricity generation: concentrated solar power (CSP) plants. Such renewable technology found in Chile a very favorable condition. Recent researches indicate Atacama Desert as one of the best regions for solar energy worldwide, having an average radiation higher than in places where CSP plants are currently implemented, e.g. Spain and USA. The aim of this study is to present an analysis of levelized energy cost (LEC) for different power capacities of CSP plants placed in distinct locations in northern Chile. The results showed that CSP plants can be implemented in Atacama Desert with LECs around 19 (sic)US$/kWh when a gas-fired backup and thermal energy storage (TES) systems are fitted. This value increases to approximately 28 (sic)US$/kWh if there is no backup system. (C) 2012 Elsevier Ltd. All rights reserved.

Abstract: In order to improve the thermal efficiency of building thermal energy storage (TES) systems, the feasibility of using encapsulated phase change materials (EPCMs) as heat storage media is analysed in this work. Specifically, the finite element method is used to perform thermal behaviour analyses of several EPCMs. These analyses include technical and economic assessments in order to identify the best combination of PCM and shell material, using as main parameters: thermal energy storage, heat transfer rate, materials cost, among others. The results show that EPCMs composed by Na2SO4 center dot 6H(2)O as PCM and covered by stainless steel highlight as TES materials.

Abstract: Determining the availability of renewable sources on a particular site would result in increasing the efficiency of buildings through appropriate design. The overall aim of the project is to develop a pioneering software tool allowing the assessment of possible energy sources for any building design project. The package would allow the user to simulate the efficiency of the Passive Solar Space Heating referred in the Low and Zero Carbon Energy Sources (LZCES) Strategic Guide stated by the Office of the Deputy Prime Minister (2006) and the Building Regulations. This research paper presents the tool for modelling the passive solar sources availability in relation to low-carbon building. A 3-month experimental set up monitoring a solar house in West Lothian, Scotland, was also undertaken to validate the simulation tool. Experimental and simulation results were found in good agreement following a one-to-one relationship demonstrating the ability of the newly developed tool to assess potential solar gain available for buildings. This modelling tool is highly valuable in consideration of the part L of the Building Regulations (updated in 2010).

Abstract: Chile is undergoing a remarkable energy matrix transition to renewable energy. Renewable energies are expanding extraordinarily fast, exceeding earlier predictions. As a result, the country is expected to meet its 2025 goal of generating 20% of its electricity from renewable energy sources quite before. Chile has become one of the first countries in the world with subsidy-free markets, where renewable projects compete directly with other conventional sources. Favorable market conditions and successful policy reforms were keys to fostering this renewable energy development. Although the country has achieved a substantial growth in renewable energy investment in a relatively short period of time, this optimism should be treated with caution. A successful transition requires a combination of a clear decision making, persistent and consistent government policies, and a clear commitment to tackling challenges to accommodate renewable energy in the power system. In this context, this paper analyses the Chilean renewable industry and the required government policies to succeed in this transition. For this purpose, we identify several critical factors that have attracted and that could attract investment to the renewable energy sector and propose key recommendations to effectively address the major challenges faced for the future development of the industry.

Abstract: Thermal energy storage (TES) transfers heat to storage media during the charging period, and releases it at a later stage during the discharging step. It can be usefully applied in solar plants, or in industrial processes, such as metallurgical transformations. Sensible, latent and thermo-chemical media store heat in materials which change temperature, phase or chemical composition, respectively. Sensible heat storage is well-documented. Latent heat storage, using phase change materials (PCMs), mainly using liquid solid transition to store latent heat, allows a more compact, efficient and therefore economical system to operate. Thermo-chemical heat storage (TCS) is still at an early stage of laboratory and pilot research despite its attractive application for long term energy storage. The present review will assess previous research, while also adding novel treatments of the subject. TES systems are of growing importance within the energy awareness: TES can reduce the LCOE (levelized cost of electricity) of renewable energy processes, with the temperature of the storage medium being the most important parameter. Sensible heat storage is well-documented in literature and applied at large scale, hence limited in the content of the present review paper. Latent heat storage using PCMs is dealt with, specifically towards high temperature applications, where inorganic substances offer a high potential. Finally, the use of energy storage through reversible chemical reactions (thermo-chemical Storage, TCS) is assessed. Since PCM and TCS storage media need to be contained in a capsule (sphere, tube, sandwich plates) of appropriate materials, potential containment materials are examined. A heat transfer fluid (HTF) is required to convey the heat from capture, to storage and ultimate re-use. Particle suspensions offer a valid alternative to common HTF, and a preliminary assessment confirms the advantages of the upflow bubbling fluidized bed and demonstrates that particulate suspensions enable major savings in investment and operating costs. Novel treatments of the TES subject in the review involve the required encapsulation of the latent and chemical storage media, the novel development of powder circulation loops as heat transfer media, the conductivity enhancement of PCMs, the use of lithium salts, among others. (C) 2015 Elsevier Ltd. All rights reserved.

Abstract: Heat capture and storage is important in both solar energy projects and in the recovery of waste heat from industrial processes. Whereas heat capture will mostly rely on the use of a heat carrier, the high efficiency heat storage needs to combine sensible and latent heat storage with phase change materials (PCMs) to provide a high energy density storage. The present paper briefly reviews energy developments and storage techniques, with special emphasis on thermal energy storage and the use of PCM. It thereafter illustrates first results obtained when encapsulating NaNO3/KNO3-PCM in an AISI 321 tube, as example of a storage application using a multi-tubular exchanger filled with PCM. To increase the effective thermal conductivity of the PCM, 2 inserts i.e. metallic foam and metallic sponge are also tested. Experimental discharging (cooling) rates are interpreted by both solving the unsteady-state conduction equation, and by using Comsol Multiphysics. Predictions and experimental temperature evolutions are in fair agreement, and the effect of the inserts is clearly reflected by the increased effective thermal conductivity of the insert-PCM composite. Application of Comsol to predict the mechanical behavior of the system, when melting and associated expansion increase the internal pressure, demonstrates that the pressure build-up is far below the Young's modulus of the AISI 321 encapsulation and that this shell will not crack (C) 2014 Elsevier Ltd. All rights reserved.