|
|
Baier, R. V., Raggio, J. I. C., Arancibia, C. T., Bustamante, M., Perez, L., Burda, I., et al. (2021). Structure-function assessment of 3D-printed porous scaffolds by a low-cost/ open source fused filament fabrication printer. Mater. Sci. Eng. C-Mater. Biol. Appl., 123, 111945.
Abstract: Additive manufacturing encompasses a plethora of techniques to manufacture structures from a computational model. Among them, fused filament fabrication (FFF) relies on heating thermoplastics to their fusion point and extruding the material through a nozzle in a controlled pattern. FFF is a suitable technique for tissue engineering, given that allows the fabrication of 3D-scaffolds, which are utilized for tissue regeneration purposes. The objective of this study is to assess a low-cost/open-source 3D printer (In-House), by manufacturing both solid and porous samples with relevant microarchitecture in the physiological range (100?500 ?m pore size), using an equivalent commercial counterpart for comparison. For this, compressive tests in solid and porous scaffolds manufactured in both printers were performed, comparing the results with finite element analysis (FEA) models. Additionally, a microarchitectural analysis was done in samples from both printers, comparing the measurements of both pore size and porosity to their corresponding computer-aided design (CAD) models. Moreover, a preliminary biological assessment was performed using scaffolds from our In-House printer, measuring cell adhesion efficiency. Finally, Fourier transform infrared spectroscopy ? attenuated total reflectance (FTIR?ATR) was performed to evaluate chemical changes in the material (polylactic acid) after fabrication in each printer. The results show that the In-House printer achieved generally better mechanical behavior and resolution capacity than its commercial counterpart, by comparing with their FEA and CAD models, respectively. Moreover, a preliminary biological assessment indicates the feasibility of the In-House printer to be used in tissue engineering applications. The results also show the influence of pore geometry on mechanical properties of 3D-scaffolds and demonstrate that properties such as the apparent elastic modulus (Eapp) can be controlled in 3D-printed scaffolds.
|
|
|
|
Martinez, C., Aguilar, C., Briones, E., Guzman, D., Zelaya, E., Troncoso, L., et al. (2018). Effects of Zr on the amorphization of Cu-Ni-Zr alloys prepared by mechanical alloying. J. Alloys Compd., 765, 771–781.
Abstract: This work presents the effects of high energy milling with different Ni and Zr ratios on the amorphization of ternary Cu-Ni-Zr alloys (initially, Cu-43Ni-7Zr, Cu-12Ni-31Zr, Cu-33Ni-7Zr, and Cu-12Ni-23Zr; and later, Cu-23Ni-15Zr and Cu-11Ni-7Zr). Microstructure was determined using X-Ray diffraction and electron microscopy. Results were compared to thermodynamic models. In the ternary alloys under study, the lattice parameter of the Cu-Ni solid solution was generally correlated to the amounts of nickel incorporated into the Cu lattice. However, longer milling times reduced that lattice parameter and facilitated Zr insertion into the solid solution. For example, after 5 h of milling time, microstructural analysis showed the formation of a solid solution with cubic structure in Cu-43Ni-7Zr. This pattern is consistent with the presence of a lattice parameter between that of Cu and Ni (alpha-phase); in contrast, the Cu-33Ni-7Zr alloy showed an alpha-phase and another similar to Zr. Results suggest that, as the amount of nickel increases, the ability to form an amorphous phase decreases. Additionally, experimental and thermodynamic data showed a solid-solution formation stage, followed by an amorphous phase formation stage that occurred as milling time and Zr content increased. (C) 2018 Published by Elsevier B.V.
|
|
|
|
Varona, J., De Fazio, R., Velazquez, R., Giannoccaro, N. I., Carrasco, M., & Visconti, P. (2020). MEMS-based Micro-scale Wind Turbines as Energy Harvesters of the Convective Airflows in Microelectronic Circuits. Int. J. Renew. Energy. Res., 10(3), 1213–1225.
Abstract: As an alternative to conventional batteries and other energy scavenging techniques, this paper introduces the idea of using micro-turbines to extract energy from wind forces at the microscale level and to supply power to battery-less microsystems. Fundamental research efforts on the design, fabrication, and test of micro-turbines with blade lengths of just 160 μm are presented in this paper along with analytical models and preliminary experimental results. The proof-of-concept prototypes presented herein were fabricated using a standard polysilicon surface micro-machining silicon technology (PolyMUMPs) and could effectively transform the kinetic energy of the available wind into a torque that might drive an electric generator or directly power supply a micro-mechanical system. Since conventional batteries do not scale-down well to the microscale, wind micro-turbines have the potential for becoming a practical alternative power source for microsystems, as well as for extending the operating range of devices running on batteries.
|
|
